1.) (PN# A405)
Console Assembly, Commander & HO: Console assembly is conveniently removed to access
the internal components of your Slide-In Carpet Cleaning Machine.
2.) (PN# J412-4)
Choke Cable: A
heavy duty choke cable controls the choke on your machine.
3.) (PN# A031)
Handle - Console Assembly, Commander & HO: Convenient handle for lifting the top console on
and off your machine.
4.) (PN# A094A)
Indicator Light, Red: The machine will tell the operator the status of the operating features of
the machine. When these
lights are activated they will inform the operator
which system shut down the unit.
These safety features include: low engine oil switch, full
recovery tank & high solution temperature.
5.) (PN# A094)
Indicator Light, Green: A green light to indicate a your if truckmount is in diverter mode.
6.) (PN# J304)
Ignition Switch, Kohler Engines: Remote Ignition located on the front of the face
panel allows for easy starting the machine.
7.) (PN# K012)
Flexible Draw Latch: An easily manipulated rubber draw latch that seals your console assembly
closed.
8.) (PN# A010)
Tiny Tach / Hourmeter: White Magic slide-in machines are all equipped with a digital tachometer
and hour meter. Produced
by KOHLER® this precise gauge gives the true RPM
of the engine.
9.) (PN# B073)
20 Amp Circuit Breaker: Protects the electrical components of your White Magic Truckmount.
10.) (PN# A0305)
Temperature Gauge: Designed for ease of operation simply, pull the trigger and watch your temperature
soar. The gauge will read
up 330°F and its sending unit is placed right before the heated
solution exits the machine. This
added benefit allows the operator to know the exact temperature
output (within a few degrees), at the wand.
11.) (PN# J412-3)
Throttle Cable:
User friendly, the choke and throttle cables easily pull out and
with just a twist locks at the desired setting.
12.) (PN# A015A)
Vacuum Gauge:
This glycerin filled gauge displays the vacuum lift of the blower,
routine check of this gauge during operation will help determine
if maintenance of the vacuum system is required.
13.) (PN#
A101) Blower Lubrication Port: Conveniently located on the face panel of the machine,
allows for proper lubrication of the blower.
14.) (PN# A061-15)
Water Recovery Switch: With just a flip of this switch the machine can go from normal carpet cleaning
operation in to water extraction.
When this switch is activated it automatically turns the
pump clutch off and closes both of the heat diverters.
Now with no heat entering the heat exchange system and the
pump not working the machine can run for days with out ever having
to supply the machine with water.
This is an absolute must for water damage operations.
15.) (PN# A138M)
Temperature Controller: This fully adjustable feature controls the HeatSmartTM system.
When the desired temperature is selected the machine automatically
regulates the exhaust diverters to maintain the proper temperature.
16.) (PN# J032-3)
Engine Kill Override: When one of the three kill switches shuts the machine down, by pressing this
button it allows the operator to diagnose the systems and make corrections
to restart the machine.
17.) (PN# B301)
Auto Pump-out Control: Every White Magic machine is pre-wired for our external Auto Pump-out System
regardless if the machine is ordered with one or not, its there
for future use if necessary.
18.) (PN# B115)
Magnesium Sacrificial Anode: Protect your water storage tank with this magnesium anode. Replace every
6 months or as needed.
19.) (PN# L003)
Ceramic Coated Exhaust Tip: Chrome plated will look great even after years of use. The exhaust from both the blower and engine
exit the machine through the face panel.
It can also be installed so the exhaust may be run down through
the floor of the vehicle.
20.) (PN# B0385)
Water Tank Drain Valve: A 1” ball valve used to drain the fresh water tank.
21.) (PN# E268)
Oil Drain Valve:
All the oil drains on the machines are installed into a central
line that is accessible in the front of the machine.
This allows for simple oil changes with little or no mess
to clean up after. No more
spilling oil all over the inside of the machine.
22.) (PN# E021)
Overflow Protection: This port allows for the proper operation of both the water box and fresh
water tank (if equipped) and prevents premature failure of the water
system.
23.) (PN# B097)
Auxiliary Output Valve: This allows access to warm water straight out of the face panel on the machine.
It is an outstanding benefit for filling sprayer or diluting
chemicals.
24.) (PN# TA70)
70 Gallon Submount Fresh Water Tank (Optional): An optional
submount water tank that conveniently saves space in your van and
holds 70 gallons of fresh water to feed your machine.
25.) (PN# B002)
Water Supply Input: Whether the machine is equipped with a fresh water tank or not, the water
supply is connected here.
26.) (PN# B001)
Solution Disconnects: Two disconnects gives this machine limited dual wand capabilities. Located far away from any electrical components.
The disconnects allow for easy hook up of live reels or wands.
27.) (PN# B085)
Chemical Selector Valve: This three-way valve allows the operator to turn on, off, or prime the chemical
system. The priming mechanism
is vacuum assisted which allows a complete & instantaneous prime
each and every time.
28.) (PN# A019)
Chemical Flow Meter: The chemical flow meter displays the flow of chemical going to the cleaning
tool. Read in GPH (gallons
per hour) this is a more consistent chemical flow compared to other
systems that meter CCM.
29.) (PN# B086)
Chemical Adjustment Knob: By turning this knob it allows the operator to adjust the chemical flow
from 0-5 GPH.
30.) (PN# A151M)
Unloader Valve: This allows the operator to adjust the working
pressure of the pumping system of the machine. Unlike a pressure regulator system the unloader
valve releases the pressure off of the pump and pump components
preventing premature failure of the pumping system.
31.) (PN# A109)
Pressure Gauge: The pressure gauge tells the operator the setting
of the unloader valve and the pressure output of the pump
|
