Right Side View:
1.) (PN# A405-1L)
Front Console w/Partition Baffle: (face panel) One of the most important feature of
any slide in system, but the most over looked is the Partition Baffle. The Partition Baffle is responsible in preventing
the re-circulation of heated air generated by the engine & heat
exchange system. All White
Magic slide-ins have been designed with this feature in mind. The signature series partition baffles are
connected by gasket materials to the air intake of the engine housing
to insure proper air flow of the machine is achieved.
2.) (PN# J345)
Engine: (28 HP KOHLER AEGIS® Liquid
Cooled Engine) KOHLER AEGIS® Engines are designed
with overhead -valves, exclusive hydraulic valve lifters, full pressure
lubrication.
3.) (PN# A103-50)
Pump Disengagement Clutch: This allows the machine to quickly go between carpet cleaning operations
to flood extraction work. With
just a flip of the switch the pump clutch disengages, stopping the
pump from functioning. The
clutch & belts are covered by an aluminum safety guard,
protecting the operator and machine from harm.
4.) (PN# A103)
CAT PUMP® 5CP
Pump: Far
superior from any other pump manufacturers, CAT PUMP® delivers outstanding reliability and performance.
Mounted in the machine high above all other components allows
for quick and easy service of the pump.
While performing service the pump does not need to be un-bolted
or readjusted, all service can be done in place.
This saves hours of down time and expense to the equipment
owner.
5.) (PN# A103-70) Pulsation Hose: As
the ceramic plungers of the CAT Pump push water into the system,
a vibration is given off. The
pulsation or vibration is absorbed helping prevent premature failure
of fittings and components.
6.) (PN# WB300) Water Box: Constructed from Stainless Steel, the water box provides
the incoming water to the pump.
The box can contain a max. of
(2) gallons of water and has a whole host of features. Located above all of the other components the
water box is hung in place and secured with only (1) ¼” 20 bolt,
allowing the box to be quickly removed if service is necessary. The water box has (4) easy to remove thumb-screws
that holds down the gasketed cover, preventing water from spilling
over on to the machine. The
water box also has overflow protection, filtered input and allows
for simple winterization of the machine in cold weather climates.
7.) (PN# B098) Water Pressure Reducer: Located
on the input of the water box the pressure reducer assures that
the input water pressure is consistent, for extra protection of
the internal float valve.
8.) (PN# A1010) ROOTS™ 47 Blower: White Magic has selected DRESSER ROOTS™
as our exclusive vendor for Vacuum Blowers. The Commander is
outfitted with the ROOTS™ 47
blower providing 460 CFM and 14”Hg of vacuum lift. These blowers
are capable of producing exceptional performance for all aspects
of upholstery cleaning to water extraction. The dual lobe blower design is far superior and more reliable to
the new tri-lobe blower designs available in the cleaning industry.
9, 11.) (PN# J735,J740,J745) Progressive Silencing System: White Magic engineers have worked tirelessly
to maximize performance without restricting airflow. The Progressive Silencing system works by stepping
down the noise generated by the carpet cleaning system at specific
locations throughout the machine.
10.) (PN# MF2100) Frame
Assembly: Constructed from heavy gauge steel, the frame
also provides easy lifting with its built in fork lift pads.
12.) (PN# B0786) 3” Muffler Clamp: High Quality, Heavy Duty muffler clamps
hold the exhaust system in our truckmounted cleaning systems.
13.) (PN# B0085) Blower Oil Lever Sight Tube: Made of High Quality TYGON Tubing, this sight
tube provides easy views of the blower oil level.
14.) (PN# G036) Blower V-Belts: (2) 36” Industrial Strength V-Belts drive
your vacuum blower.
15.) (PN# G038) Pump V-Belts: (2) 38” Industrial Strength V-Belts drive
your high pressure pump.
16.) (PN# J710) Exhaust Pipe: Directs exhaust gasses out of the front of
your machine and out of the van.
Left
Side View:
1., 19) (PN#
HE2200-1, HE2200-2) Heat Exchange System: Making up
the heart of the Heatsmart™ Technology is our
double barrel heat exchanger.
Constructed using White Magic exclusive High Efficiency Finned
Copper Coil, this coil is far superior to other coil designs found
elsewhere in the United States. The heat exchanger is designed to maximize
both airflow and heat transfer. As the water flows through the heat
exchanger it enters at the coolest point and exits the heat exchanger
at the hottest point. This
is commonly referred to as Reverse Flow.
2.) (PN# B135P)
Pressure Relief Valve: This valve is factory set to prevent over
pressurization of the machine.
When the machine reaches its setting the valve opens to relieve
excess pressure being developed by the pumping system. This valve
allows the operator to adjust the pressure up to 1200 PSI for tile
and grout cleaning.
3, 4, 5.) (PN#
A380, A381, A383) Vacuum Actuators: Opens and
closes the Heat Diverters to maintain and control water temperature.
6, 8 - 12, 20.) (PN#
H011, H0155, H016, H017) Stainless Steel Braided Hoses: White Magic uses only Stainless Steel high-pressure
hoses to interconnect the systems solution and pumping system.
7.) (PN# H425)
Flexible Hose, Air Input: Connects the Air Cleaner on your machine to the fresh outside air.
13.) (PN# H013)
Chemical Jug Input Line: Connects your chemical pump to your mixed
chemical in the chemical jug.
14.) (PN# A140M)
Vacuum Solenoid: As the temperature reaches its predetermined
setting established by the operator, the Temperature Sensor sends
an electrical signal to the vacuum solenoid which activates the
Vacuum Pods to open and close the Heat Diverters to maintain the
desired operating solution temperatures.
15.) (PN# J790)
Tube Clamp: Connects your chemical pump to your mixed
chemical in the chemical jug.
16.) (PN# J720)
Engine Exhaust Diverter: This component operates by directing the
flow of hot gases produced by the engine. During operation of the
machine the heat generated by the engines exhaust will flow into
the heat exchange system to heat the cleaning solution.
Once the cleaning solution has reach the pre-determined temperature
set by the operator the temperature sensor will activate the vacuum
diverter control closing the Exhaust Diverter preventing the hot
gases from entering the heat exchange systems. The Heat Diverters internal components are
made from Stainless Steel and are nickel-plated to extend life of
thediverter.
17.) (PN# J715) Blower Exhaust Diverter: Working in
conjunction with the engine exhaust diverter is White Magic’s exclusive
blower exhaust diverter. This
diverter protects the system from over heating.
After the engine exhaust diverter has closed, and if the
solution temperature continues to rise, the blower exhaust diverter
will then activate, preventing any of the heat generated by the
blower from entering the Heat Exchange System.
This is an exceptional feature for water recovery operations. When the machine is placed into water recovery mode both the Engine
Exhaust Diverter and Blower Exhaust Diverter are activated. This prevents any heat generated from entering
the heat exchange system, allowing the machine to run continuously
for hours with no water in the system.
18.) (PN# D0029B) Heavy Duty Spring:
Assists
the blower diverter in closing while under a vacuum load.
21.) (PN# J0347)
High Temperature Kill Switch: This safety feature protects the operator,
bystanders and the machine from dangerous overheating of the systems
water temperature rating. This
Safety Kill Switch will shut the machines engine down if the solution
temperature exceeds 275°F. If
this occurs the operator can quickly determine the cause or the
shut down by looking at the indicator lights on the face panel of
the machine.
|
